This section describes how to install and set up Cumulus VX in VirtualBox to create the two leaf and one spine topology shown below.
The best part is you can practice using GNS3 and Cumulus VX locally on your laptop! Cumulus Linux combines the power of Open Networking with a network operating system that runs on top of industry standard networking hardware from vendors such as Dell, HP, Quanta and others. Founded by veteran networking engineers from Cisco and VMware, Cumulus. GNS3 2.0 New Features Smart packet capture and capture on any link (4:07) GNS3 2.0 New Feature Support for color-blind users (2:02). Cumulus VX (Linux Networking Operating System) Cumulus VX Introduction (0:43) Cumulus VX FAQs (1:29). VirtualBox and GNS3 This section describes how to install and set up Cumulus VX with VirtualBox and GNS3 to create the two leaf and one spine topology shown below. In the topology, leaf01 and leaf02 are the access layer switches on the network. Leaf01 and leaf02 connect to spine01, which is the aggregation layer switch on the network.
In the topology, leaf01 and leaf02 are the access layer switches on the network. leaf01 and leaf02 connect to spine01, which is the aggregation layer switch on the network. To facilitate additional configuration after the initial setup descibed in this guide, leaf01 and leaf02 also have two connections to each other.
The course includes hands on demonstrations using both Cumulus VX and physical switches. The best part is you can practice using GNS3 and Cumulus VX locally on your laptop! Cumulus Linux combines the power of Open Networking with a network operating system that runs on top of industry standard networking hardware from vendors such as Dell, HP.
Follow the steps below to:
- Create three VMs (leaf01, leaf02, and spine01) and the network connections between them
- Log into the switches
- Perform basic switch configuration
- Verify configuration
These steps were tested with Cumulus VX 4.2 and VirtualBox version 6.1.12 on macOS version 10.14.6.
Create and Configure the VMs
The following procedure creates leaf01, leaf02, and spine01 and the network connections between them. This section assumes you have VirtualBox experience.
Download and Install the Software
- Download and install VirtualBox.
- Download the OVA VirtualBox image.
Create the VMs
The Cumulus VX OVA image defines the CPU, memory, and disk requirements. Cumulus VX requires at least 768MB of RAM and 6GB of disk space.
CumulusVX versions 4.3 and later requires 2 vCPUs.
Follow these steps for each VM (leaf01, leaf02, and spine01)
- Open the VirtualBox application and select Import Appliance from the File menu.
- Browse for the OVA disk image you downloaded, click the Open button, then click Continue.
- In the Appliance settings, change the name of the VM to
leaf01, then click Import to begin the import process.
- In the VirtualBox Manager window, right click the
leaf01VM, then select Clone.
- Change the name of the VM to
leaf02, then click Continue.
- Make sure Full Clone is selected, then click Clone.
- Repeat steps 4 through 6 to create
Create Network Connections
VirtualBox network adapters start with eth0, then swp1, swp2 and swp3. Settings for Adapter 1 are applied to eth0, settings for Adapter 2 are applied to swp1, and so on.
Configure the network adapter settings for leaf01, leaf02, and spine01 to create point-to-point connections, as shown below.
Follow these steps for each VM (leaf01, leaf02, and spine01):
In the VirtualBox Manager window, select the VM.
Click Settings, then click Network.
Configure the Adapters on each VM as shown below, then click OK to save the network connections.
- Make sure to select the Paravirtualized Network (virtio-net) network Adapter Type for all adpaters
- Enable Promiscuous Mode for all adapters (except Adapter 1) to allow for LACP bonding to operate properly.
- Do not change the MAC Addresses, which are configured automatically.
Power on the VMs.
Log into the Switches
Cumulus Vx Gns3 Vs
Log into each switch with the
cumulus account and default password
cumulus. When you log in for the first time, you are prompted to change the default password.
Cumulus Vx Gns3 Plus
If you are using Cumulus VX 4.1.1 or earlier, the default password is
CumulusLinux!. You are not prompted to change the default password.
For more information on the required password change, see the Cumulus Linux documentation.
Basic Switch Configuration
Run these commands on each switch to change the hostname and bring up theinterfaces. Exit the switch, then log back in to see the new hostname at theprompt.
Run the following commands on each switch to verify the configuration:
It might take a few minutes for the LLDP information to update. If your command output is different from the output shown below, wait a few minutes, then run the command again.
Cumulus Vx Gns3 Pro
Run the following commands on each switch to show system information:
Cumulus Vx Gns3 For Sale
- Read the Cumulus Linux User Guide to learn about using Cumulus Linux and test out features on your switches.
- Visit the NVIDIA Cumulus web site, which offers many resources to help you understand Cumulus Linux.
- Try some of the advanced configuration. You can update your virtual environment to be able to use the Cumulus Linux on demand self-paced labs (a quick and easy way to learn the fundamentals). You can also run the topology converter to simulate a custom network topology with VirtualBox and Vagrant, or KVM-QEMU and Vagrant.
- Try Cumulus in the Cloud, which is a free, personal, virtual data center network that provides a low-effort way to see Cumulus Networks technology in action. This is a good way to try out Cumulus Linux if you have platform or disk limitations.